LED Whips By SpudState Whips

Standard LED Whip       (For Information Contact Tom at tomz@tzhomes.com.)

SpudState Whips Standard LED Whip comes with 3 Key Controller, power cord, spring, and flag. Comes in 3’, 4’,5’, 6’, or 7’ lengths in Black or White. SpudState Whips uses a 3/8”-24 thread that is compatible with most CB Antenna Springs and mounts. With the 3 Key controller you do not need a remote. Easy to dim, speed adjustment, has many kinds of modes, such as static colors, gradual changes, strobe, etc. Auto memorizing function, saving your last setting. It has 19 dynamic modes and 20 static colors.  SpudState Whips are wrapped over 3/8” Fiberglass Rod. The Fiberglass Rod is specifically formulated to be outdoors in the elements, glued into a custom built 6061 T6 hex ferrule with 3/8”-24 threads, and then covered with heat shrink PVC tubing to protect each rod from sun-splintering and deterioration, which increases durability. The 3/8″-24 threaded base is compatible with a large variety of brackets, mounts, springs, quick disconnects and other mounting hardware. The Standard LED Whip does not chase, stack, meteor, or have many of the functions of the Super LED Whip.

Adding a Quick Disconnect makes it quick & easy to install and remove your whip from your vehicle.


Standard LED Whip With Radio Frequency (RF) Remote

SpudState Whips Standard LED Whip with RF Remote comes with RF Remote, RF Wireless Controller, power cord, spring, and flag. Comes in 3’, 4’,5’, 6’, or 7’ lengths in Black or White. They use a 3/8”-24 thread that is compatible with most CB Antenna Springs and mounts. It has 19 dynamic modes, 20 static colors, speed adjustment, brightness adjustment, demo mode, ect. Does everything the Standard LED Whip will do but with a Remote. The Standard LED Whip does not chase, stack, meteor, or have many of the functions of the Super LED Whip.

Adding a Quick Disconnect makes it quick & easy to install and remove your whip from your vehicle.


Super Dream Color Chasing Whips (Super Whip)

SpudState Whips Super Dream Color LED Whip is as good as any on the market today! Comes in 3’, 4’,5’, 6’, or 7’ lengths in Black or White. SpudState Whips are wrapped over 3/8” Fiberglass Rod. The Fiberglass Rod is specifically formulated to be outdoors in the elements, glued into a custom built 6061 T6 hex ferrule with 3/8”-24 threads, and then covered with heat shrink PVC tubing to protect ech rod from sun-splintering and deterioration, which increases durability. The 3/8″-24 threaded base is compatible with a large variety of brackets, mounts, springs, quick disconnects and other mounting hardware. SpudState Whips uses only quality Dream Color LED Waterproof Light Strips to make their Whips. They have 133 different changing patterns, 100 different speeds, and 7 static colors. They stack, chase, fade, flash, jump, strobe, meteor, and more! The Dream Color Chasing LED Strips are wrapped on the 3/8” fiberglass rods and covered with clear heat shrink which helps protect the LEDs from damage. The cap on the end of the 3/8” fiberglass rod has the heat shrink over it so brush and tree branches don’t knock the end cap off. Our Dream Color LED lights go all the way up and don’t stop for a flag (7’ only have about 6’ 3” of lights and a Safety Flag on top). A Safety Flag comes with each Whip. The controller, RF remote, battery for RF remote, a 5.5×2.1mm DC Power Male Plug, 10FT Extension Cable to allow you to locate the controller were you want, users manual, and a spring is provide with each whip.

Included: Super Dream Color LED Whip, LED Controller, LED RF Remote Control & Battery, 12V DC Male Plug, 2 Controller to Whip Cables, 10FT Extension Cable, and a Heavy Duty Chrome Spring.

The LED Controller and Remote are not waterproof. Controller must be located so it does not get wet. (The controller will run 2 whips and synchronize a pair.)

Adding a Quick Disconnect makes it quick & easy to install and remove your whip from your vehicle.


Quick Disconnect

SpudState Whips Quick Disconnect makes it quick and easy to remove your Flag pole or whip from your UTV/ATV other Off-road Vehicle! Just pull one pin and your flag pole or whip is ready to be removed! Your flag pole or whip can be installed just as easy, just pull the pin, slide your flag pole on, and put the pin back in! You are ready for a fun day of riding.

SpudState Whips Quick Disconnect are manufactured from Polished Billet 6061-T6 Aircraft quality aluminum. Stainless Steel ¼ inch Detent Pin to quickly remove you ATV/UTV flag pole or whip. Threaded for any flag pole or whip with 3/8”-24 threads. Most CB or flag pole Springs use a 3/8”-24 thread. Firestik flag poles or whips made with Firestik flag poles use a 3/8”-24 thread.

SpudState Whips Quick Disconnect are easy to install! Install the Male Bottom Half on your UTV, ATV, or other Off-road Vehicle. The Male Bottom Half installs on the vehicle and not the Female Top Half  to collect sand and debris. Connect the Female Top Half to your flag pole or spring. Use any ¼” rod through the pin hole in the Male Bottom Half to hold it in place while you tighten the 3/8” bolt and the Female Top Half to a flag pole or spring. My number 2 Philips Screw Driver is just the right size. Slip the Female Top over the Male Bottom and install the Detent Pin. Pull the Detent Pin and your flag pole or whip comes right off. Enjoy Riding!

Included:
Female Top Half 6061-T6 Aircraft Quality Aluminum
Male Bottom Half 6061-T6 Aircraft Quality Aluminum
1/4″ Stainless Steel Detent Pin
3/8″-24 Thread Bolt
3/8″ Flat Washer
3/8″ Lock Washer

Contact Tom at tomz@tzhomes.com.